![]() ![]() This functionality helps visualize where the designed oligos are located with respect to both the regions.Įvaluates pre-designed primers and designs a compatible primer a given sense or anti-sense primer. This helps verify the SYBR® Green primer design and visualize primer and amplicon specificity.īeacon Designer™ identifies template structures and then automatically avoids them while designing SYBR® Green primers.ĭisplays the regions of homology and secondary structures for the sequence graphically in the Sequence View pane. The SYBR® Green primers designed can be BLAST searched against genomic databases available at NCBI. If you downgrade from Release 8.2.100.0 to a 7.x release, the trap configuration is lost and must be reconfigured.Beacon Designer™ Features SYBR® Green Primer Designĭesigns primers optimized for SYBR® Green PCR assays.īeacon Designer™ designs highly specific SYBR® Green primers by BLAST searching sequences, automatically interpreting the results and then designing SYBR® Green primers by avoiding regions of significant homology.For more information about the stock-keeping units (SKUs) for the AP802s and the Cisco ISRs, see the following data sheets:īefore you use a Cisco AP802 series lightweight access point with Cisco Wireless Release 8.2.100.0, you must upgrade the software in the Cisco 880 Series ISRs to Cisco IOS 15.1(4)M or later releases.Īll other reg. Note Cisco AP802 is an integrated access point on the Cisco 800 Series Integrated Services Routers (ISRs). – Added Telnet to the list of unsupported features – Rephrased the statements made in this section. – Added a statement that Cisco Aironet 3600 Series APs cannot recognize the reload command. – Added information about Cisco CMX support. – Documented CSCux75436 kernel route issue. – Added CSCuw03323 to the Resolved Caveats list. – Added a Note on Release 8.2 related interface restrictions – Added Application Visibility and Control (AVC) for FlexConnect centrally switched access points to the list of not supported features. You must manually reconfigure the mobility MAC address after the upgrade.” – Added this statement: “If you upgrade from Release 8.0.110.0 to a later release, the config redundancy mobilitymac mac-addr command's setting is removed. Upgrading to Cisco WLC Software Release 8.2.100.0.– Added: Removal of Support for Rx SOP from Mesh Backhaul – Added: EoGRE (Supported in only local switching mode) Features Not Supported on Cisco 2504 WLC.– Added Wired Guest and FlexConnect central switching. – Added SIP snooping with FlexConnect in local switching mode Features Not Supported on Cisco Aironet 18 APs.– Modified information about FlexConnect central switching. Features Not Supported on Cisco Virtual WLCs.Obtaining Documentation and Submitting a Service Request Upgrading from an LDPE to a Non-LDPE Cisco WLCįeatures Not Supported on Cisco WLC Platformsįeatures Not Supported on Cisco WiSM2 and Cisco 5508 WLCįeatures Not Supported on Cisco Flex 7510 WLCsįeatures Not Supported on Cisco 5520, 8510, and 8540 WLCsįeatures Not Supported on Cisco Virtual WLCsįeatures Not Supported on Access Point Platformsįeatures Not Supported on Cisco Aironet 18 APsįeatures Not Supported on Cisco Aironet 1550 APs (with 64-MB Memory)Ĭisco Mobility Express Solution Release NotesĬompatibility with Other Cisco Wireless Solutions Special Notes for Licensed Data Payload Encryption on Cisco Wireless LAN Controllersĭownloading and Installing a DTLS License for an LDPE Cisco WLC Upgrading to Cisco WLC Software Release 8.2.100.0 (GUI) Upgrading to Cisco WLC Software Release 8.2.100.0 Software Release Types and Recommendations Software Release Support for Access Points Increased Channel and Tx Power Support for Various CountriesĬisco Industrial Wireless 3702 Access Point Updates Support for Wi-Fi Certified Passpoint Release 2.0 Pre-Shared Key Provisioning Support for Mesh Networksĭynamic Management User Login via AAA Server Removal of Support for Rx SOP from Mesh Backhaul Increased AP and Client Scale for Cisco Virtual Wireless ControllerĪccess Point Provisioning using Plug-n-Play (PnP)Įnhanced wIPS Support for Hyperlocation Module with Advanced SecurityĬisco Air Time Fairness: Client Fair Sharing Unsupported Cisco Wireless Controller Platforms Supported Cisco Wireless Controller Platforms ![]() Release Notes for Cisco Wireless Controllers and Lightweight Access Points for Cisco Wireless Release 8.2.100.0Ĭisco Wireless Controller and Cisco Lightweight Access Point Platforms
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |